Most car enthusiasts have a garage that often serves not only as a refuge for the beloved car, and is also used as a workshop or the place of men's conversations. It often happens that in cold weather the engine warming takes time more than the trip itself, and as a result of this, the relevance of the planned trip is to be reduced to zero. Yes, and discuss with friends the latest trends in the field of vehicles are much more comfortable in the warm room. Agree that it is much better to repair cars or other events warm. Therefore, be sure to take care of the heating of the garage room.

Buy the finished stove or make it yourself?

The correct solution of the "cold" situation will be the oven for the garage with their own hands. Prepare components and assemble them will not be difficult if there are even small skills of working with different materials and tools.

When choosing a suitable type of garage oven, the main thing is:

• ease of operation;
• economical fuel consumption;
• reliability.
  Important! To choose exactly what oven, which is perfect for your needs, read the information on all sorts of types and types of design.

What are the types of furnaces?

Modern aggregates for garages presented on sale on the market have certain characteristics that allow classifying equipment. The main factor is the type of heating material.

Based on such a principle, the following types of heating equipment are distinguished:

1. Electric stove. The advantage of the electric unit is the ability to choose a stove with an optimally suitable power level. But a significant disadvantage is distinguished by a significant consumption of electricity during operation.
   Important! The design of such aggregates certainly requires a professional approach, otherwise - high risk of emergency situations.
2. Heating gas boiler. Differs in high productivity in the ratio with a small value. However, a prerequisite for installing such a device is distinguished by accessing the gas supply network. The main disadvantage of the gas boiler is a high level of danger in the event of an explosion.
   Important! To install such a furnace, the specialists will also need support, so that all the conditions of the technology of working with gas equipment are accurately complied with.
3. Aggregates, the performance of which depends on the combustion of solid fuel. Such a stove can be purchased in any specialized store or construct itself, which will reduce cash spending several times. The production of heating aggregates are engaged in both foreign manufacturers and domestic. The most popular types of such heating apparatuses are wood-hazing furnace for a garage and to "work out".
   Important! For independent design, any capacity from suitable materials or separate parts that are easy to connect to themselves are quite suitable.
4. The heating furnaces of the garage, the functioning of which occurs due to the waste machine oil is characterized by ease of use and economy.
   Important! This option is also available to create your own hands.

Requirements for the design stove for the garage

To decide on the type of stove, answer yourself a few next questions:

1. What amount are you ready to spend money on the heater?
2. What is the area of \u200b\u200bthe alleged garage premises for heating?
3. For what time do you plan to give a garage?

Important! If the garage is an extension to the residential premises, then in this case we recommend installing the unit connected to the total gas or electrical network. If this is an autonomous room that does not have any living buildings with communications - make a separate system.

So that in the process of operation, the oven did not bring the inconvenience, the following characteristics will be the following characteristics of the aggregate created:

• weight not over 30 kilograms;
• volume up to 12 liters;
• dimensions 0.7x0.5x0.35 m;
• the size of the exhaust cross section is about 0.1 m.

How to assemble the design of a wood furnace with your own hands?

The economical furnace on firewood, independently assembled, is considered the simplest in service and ideally suitable for heating autonomous garage buildings. Often in the economy of the car enthusiast is encouraging a heating structure with the name of the bourgeois.

Advantages of a wood-burning furnace

Such a stove has a lot of advantages, among which they allocate:

• ease during operation;
• efficiency;
• pretty low cost of equipment;
• high level of efficiency in relation to minor design dimensions;
• the ability to operate the oven away from communications;
• permissible use for cooking and warming up;
• the need to prepare a special foundation for the unit is excluded.
  
  Important! The only significant disadvantage of the wood stove is high consumption of inexpensive, but still standing, heating materials. Firewood in the stove is quite quickly burned and warm, in the process of burning, is not accumulated. After the furnace cease to heat, the steel case is pretty cool enough.

Features Design Stove-Bourgeys

The design of the bourgeois type stoves does not have clear regulations.

Each wizard can build this design, given its own preferences, but in any case, such a stove has basic design elements:

1. The furnace, which is a container in which the heat combustion process occurs. The dimensions of such a stove do not have clear standards.
2. Grill for laying firewood and creating thrust, which is placed at the base of the stove.
3. Chimney pipe.
4. The roller, placed under the grille, to remove the accumulated resin during the combustion process.

Important! If you upgrade the design of the bourgeitors, it will be possible to significantly save the consumption of firewood. Such an effect can be achieved if the nozzle is welded to the stove body over the door, and not, as taken, behind the wall near the wall. Thanks to this installation of the nozzle, first of all the wall structures will be heated, and only then the firewood will fall into the pipe. Due to this, the time of heat recovery will increase, since the brick, concrete-clay or insulated metal pipe is cooled much slower than the steel case.

Materials for the design of a wood-burning furnace

To assemble a wood stove yourself, you will need to purchase the following materials:

• metal barrel of 200 l;
• pipes;
• channel.
  Important! To more clearly imagine the subsequent scope of work and the required amount of consumables, preview the drawings of the furnace for the garage of different variations. Take the most simple in your opinion the design and consider in detail all nodes of the compounds of individual items.

Montaja technology

1. Gently cut the upper part of the barrel with a special hacksaw for metal or a grinder.
2. Relify sharp edges.
3. With the help of a hammer, the edges of the cropped barrel wrap inside.
4. Cover edges in the same way to fit out.
5. Cut the chisel in the center of the cover hole with a diameter of 100-150 mm for the pipe.
6. Welcome a channel to the lid.
   Important! The place where there was a traffic jam, tightly brew or leave to control the combustion process inside the stove.
7. At the top of the barrel, cut the hole, with a diameter of 150 mm for the chimney pipe.
8. Brew pipe.
9. To the hole in the lid, breed a pipe with a diameter of 100 mm so that it performs above the surface of the cover. The pipe will serve the air into the barrel.

How to exploit wood stove?

After you bring the design of the furnace, initially test it on the correct functioning. Follow these steps:

1. Fill out the stove on 1/3 firewood.
2. Install the pipe supplied to the air inside and cover the lid.
   Important! During the combustion process, the lid is slowly lowered.
3. Firewood through a pipe hole slightly moisure with gasoline or kerosene and throw the burning match.
   Important! With the right execution of all actions, the stove is capable of damping the room for 7 hours. If you fill it with firewood completely, the time of heat transfer reaches 60 hours.

Video

Browse the video in which an example of creating and operating a wood stove is clearly shown.

Stove on working out

Against the background of other similar structures, the oven for the oil garage is highlighted by the cost-effectiveness, easy operation and inexpensive combustible material. The design of the stove on the workout is similar to the design of the bourgeitry.

Advantages of application

Among the characteristic advantages are the following:

• simplicity when collecting design;
• high level of environmental friendliness, which is achieved due to the absence of soot and smoke emissions;
• mobility - the nature of the design allows you to easily disassemble and assemble the stove again;
• the process of work is carried out during the combustion of oil to be disposed of;
• safety of use, since the flame does not acquire an open character, and only evaporation of spent oil is burned;
• to the stove on working with ease, you can attach the heating system, as well as monitor the temperature mode.

Materials for construction

The oven on the development can be constructed by itself, which will not require a lot of effort and will not take much time. To build a homemade garage furnace, you will need:

• two metal containers, metal sheets of which are not less than 4 mm;
• connecting pipe with numerous holes;
• nozzle for upper tank;
• pipe for drawing.

Mounting Technology Oil Garage Oil

To construct the stove with your own hands on "Working", follow these steps:

1. For the bottom, take the container, the volume of which is within 8-15 liters.
   Important! It will be in her further fuel to pour.
2. Make a hole at the top.
3. We breed the lid so that it is convenient to operate the furnace and adjust the air intake in the process of processing the material for heating the garage.
   Important! With the help of lifting and lowering the lid, the supply required for combustion of oxygen is controlled.
4. To create the top, take the tank of the appropriate size.
   Important! The upper element in conjunction with the connective tube perform the heating role of the unit and is simultaneously furnace. The maximum temperature in such a furnace reaches 900 ° C. To avoid deformation and roasting containers, use iron, the thickness of the sheets of which is at least 4-6 mm.
5. Connect both tanks with a perforated pipe with a size of 360 mm.
   Important! If a solid-grade pipe was taken to connect, drill 48 holes with a drill with a diameter of 9 mm in this location:
   • 8 in a circle;
   • 6 in height.
6. To the top of the homemade stove weld the nozzle.
7. On the nozzle set the exhaust pipe from galvanized steel.
   Important! The ideal height of the chimney pipe is 4 meters - it will provide good craving.

As a result of the work done, you will receive an aggregate with such parameters:

• the total weight of a similar heating system up to 30 kg;
• dimensions of such a design from 0.35 to 0.7 m;
• fuel consumption at the same time will be about 1.5 liters per hour of work.

Rules of operation of the stove on "Working"

In order for the result of the work of the furnace to be justified and she fully heated the garage space, carefully read the following instructions on the operation:

1. Regularly, every 2 week spend cleaning the stove from the inside.
2. Important! If you use the purified composition of the material as a fuel, then the cleaning of the elements can be carried out much less often.
3. If you install the top pipe of the larger diameter than the exhaust, the amount of soot will be significantly reduced.
4. Installing the unit, follow in places of remote from easily flammable items.

How does the stove work?

To establish the work of the homemade oven for a garage on working out, do the following:

1. To ignite the stove, put the newspaper or paper into the lower tank and pour fuel over them over.
2. After 10 minutes, the contents of the container will boil and at the expense of its characteristic features, oil will light up independently.
3. Pull the fuel portion - 5 liters at a time.
   Important! A transformer, transmission, machine oil or diesel fuel is ideal as fuel material.

Video

To more clearly imagine the principle of the device of such a furnace and operation, look at the proposed video below.

Installation Recommendations in a brick furnace garage

The main criterion for the construction of a brick furnace is compliance with compact sizes, and in the rest of the other, the system of such a stove is similar to previous options.

To correctly build a brick stove, do not follow the following recommendations:

1. Before starting assembly, prepare the basis. To do this, spread the polyethylene film, and on top of it, pour the sand layer with a thickness of at least 1 cm.
2. On the prepared foundation, lay a brick in 11 rows.
3. For suture.
4. Repair the surface of the plate.
   Important! Heat such a furnace will radiate until the firewood blocked, and then it will begin to gradually cool. Ideal such a design for decoration of heating in a brick garage.

Conclusion

No matter what kind of furnace design for the garage you did not choose, in any case, it will give an expected result. With the help of any suggested above, an uncomplicated unit, you can always maintain a warm climate inside the garage room. And in comfortable conditions and repair works are more pleasant to perform, and talk in a circle of friends.