Garden car - the thing is very useful, because the dacket is constantly in work. It is required to move the fertilizer, the landing, then the building material, then the soil, then the garbage. Moderate physical activity, of course, is useful, but it does not apply to the raising of gravity. Having a garden wheelbarrow, you will greatly alleviate your summer life and save forces. How to make a garden wheelbarrow with your own hands, told in this article.

The difference between the trolley and wheelbarrow

Many believe that the trolley and the car are the same. In general, they are somewhere right, but there are still the difference between them:

1. The cart with one wheel is usually called a wheelbarrow. She is maneuveran and reliable, and she has a lot of ruting already than her relative. With it, you can deliver fertilizer and mulch along the narrow tracks between the beds in the garden and in the garden. The unloading of it is ease - pressed on 2 longitudinal handles, tilted to the side, everything was already in the right place. Not quite in it is good what to save equilibrium, you need to apply effort. If it is greatly loaded, then the strength requires a considerable one. In addition, if you go through sand or soft soil, then the only wheel on which all loads accounts is very falling, and it makes it difficult to move.

2. Actually, the trolley is something more solid, because it can be from 2 to 4 wheels. The tracks for her movement are needed wide. But it is stable. Pen by structural execution longitudinal or transverse. Load hard materials on it. Shees it withstands well, just to watch it is necessary, so that the center of gravity is not shifted.

If you decide this kinderVentar to have in your yard, you should know that there are carbacked cars and garden. In principle, their designs do not differ, except the first more powerful.

Single garden trolley with their own hands made of metal

Work on the creation of a garden truck will begin with a sketch:

• Denote by dimensions, point out all the necessary sizes, then the material is easier to select;
• Primary in a metal trolley is a container. Based on its size, the frame is selected, the wheel.

A single garden car belongs to the following details:

• 2 levers - 1;
• 2 handles - 2;
• 3 ribs. On the sketch at the top they are numbered 3;
• bases - 4.5;
• 2 linings - 6;
• 2 racks - 7;
• 2 slats - 8;
• stop - 10;
• transverse ribs - 9, 11;
• supports - 12;
• trough - 13;
• wheels - 14.

Now collect the necessary tool:

• saw blade for metal;
• bulgarian;
• screwdriver;
• welding inverter;
• drill;
• hammer.

Materials are needed:

• 1 mm sheet with a steel area of \u200b\u200b2 square meters. m;
• wheels;
• tube that is used as an axis. It can be replaced by replacement;
• corner for reference racks of the wheel axis 25x25 mm;
• thin-walled tube for handle and cargo racks with a diameter of 20 mm;
• nuts;
• slingles.

When everything is chosen, proceed to work.

Assembling garden bar

1. On the finished sketch we make markup.
2. Dispress the billet for the body.
3. From the billets obtained, the body component, applying welding.
4. Stripping from body sizes, collect chassis:

• We fold the base from the details 4 and 5;
• to the base we weld the lining;
• racks fastened to lining;
• to the base and racks weldings the rib 3;
• at the assembled node, we set the body and weld it to the ribs;
• apply to the upper edge of the body, the remaining edge 3 and fix it with welding;
• to the lower edge, the wall of the body and the upper edge welded the levers;
• fix on the lining levers;
• to the body welding focus 10, and to it support 12;
• to impart stiffness design, fix the edge 9.11;
• to the base we weld the plank, the holes are pre-drilled;
• insert the axis into the wheel, fix it. On this assembly of the garden plate is completed.

Trolley from barrel

Your truck will cost much cheaper if you use a metal barrel as a container. For this:

• barrel cut along;
• we make the frame in the form of the letter A;
• weld to the frame of the rack;
• fix the barrel on the ground;
• in the nose, mount the wheel.

Opposite parts serve as handles. All, car ready.

Wheels for Garden Tack

Wheels for garden carts to buy is easy, but if you have they remained from a bike or from a moped, a motorcycle, then they are quite suitable. The best pneumatic wheels, i.e. Those that turn into the pump:

• they increase car lifting capacity;
• increase the permeability. The car will be able to go through an uneven surface, it moves easier for soft soil.

Pneumatic wheels manufactured by LIV Kolesa from Slovenia have proven well established:

• they are reliable, because at the enterprise the manufacturer has a strict quality system;
• discs of these products are performed from galvanized steel and high-quality polypropylene;
• on some models, bearings have protection against moisture and small particles.

Consider an example of manufacturing a truck of a garden two-wheeled using a motorcycle wheel.

Trolleys Garden two-wheeled waste

Collecting at home all sorts of unnecessary things, for example:

• old metal bed;
• wheels from a motorcycle;
• trimming rolled metal.

You can make a wonderful garden trolley with your own hands.

We will need:

• from the bed to separate the arms and legs;
• metal 1 mm sheet;
• wheels from a motorcycle.

Production technology is simple:

• of the two bed legs and the housekeeper make a frame;
• cut out from the steel sheet of the wall and bottom of the body;
• weld the joints of parts by point welding;
• we install the container on the frame and customize the parts from the edge of the box;
• cutting walls Conduct to a frame and connect the weld;
• now skimming the joints of the container;
• we make the bridge of the wheel pair using the legs from the bed. We make axes and hubs;
• axes we connect to the pipe from 2 sides;
• turn over the body upside down and weld the bridge to it;
• we make lining in the form of brackets and strengthen the design;
• fix the wheels on the axes and return the trolley into normal position;
• we perform a handle using bed legs and backs;
• choose a convenient position of the handle and weld it;
• we provide a supporting leg with a rising, otherwise it will slow down the movement.

As a material for a garden truck, a solid tree is suitable.

Trolley gardening from wood

For the manufacture of a wooden trolley, it will be necessary:

• bars wooden 4x4 cm long 1.2-1.5 m;
• plywood;
• stilette with a thread 0.6-0.7 m, which can be replaced with a cut pipe;
• 2 wheels.

Work on the manufacture of truck garden two-wheeled with frame design. If there is a pipe, it is enough to simply bend in the form of the letter P. We have it wooden, so we kill it from bars, withsting the length to 1.5 m, and the width is up to 0.7 m, and then:

1. At the bottom of the frame drill holes. They subsequently inserted the axis. In the role of the axis, we serve a threaded stud or pipe. A part of the axis protruding from the frame on both parties is approximately equal to the double width of the wheel. The axis in the frame is mounted tightly with screws or screws, tightened nuts.
2. On the axis we dress the wheels and attribute them with linings. They can be purchased or from a bike, in general, which is found. If nothing has found, we will make the wheel yourself from thick plywood. So that it serves longer:

• soak the phaneer with an antiseptic or olifa;
• wheel with a metal strip, wear a tire or envelop thick rubber;
• in the planting holes of the wheels insert the bearings;
• lubricates wheels and axis with solidol.

3. The body turns out. We will make it from plywood too. First, cut out the bottom and rigidly fastened the part to the frame. Options are possible. They are installed motionless in relation to the bottom of the box, or with the help of loops and then they fold. Fastening is carried out like this:

• one side of the side directly to the bottom;
• the second, which, on the contrary, is concerned through the adapter in the form of a bar, its thickness is equal to the thickness of the side;
• the fastener of the endboard is carried out through the transitional dual thickness bar. Thus, the trolley in the folded state will become completely flat. So that in the working position of the side did not fall, set spiing or hooks.

Trolley - Decoration for Garden

Such a wooden trolley, the photo of which is made in the garden, the owners are used as a kashpo for flowers.

As you can see, the wheel is unusual here. Let us dwell on its manufacture.

Wooden Wheel Wheel Wheel Wheel DIY

The collective wheel consists of:

• rim;
• spokes;
• axis.

Technology is as follows:

1. For the manufacture of the rim you will need a template on the scale of 1: 1. Therefore, placing a circle on a sheet of plywood or chipboard. The diameter of it is equal to the diameter of the future wheel. The circle will come out perfect if in the center of the workpiece to score a nail, then put a rack on it along the length of an equal radius of the wheel, and on the opposite side to fasten the pencil. By rotating this improvised circulation around the nail, we get a smooth circle. We split it on 8 parts.
2. Now we make the rim, for which we take wooden planks, carefully tightened, in an amount of 8 pcs. The length of them is slightly larger than 1/8 of the circle. The ends of the bars drank at an angle of approximately 67 degrees. Having putting these details on the template, check, so qualitatively they are joined.
3. We make the marking of the axis of the wheel and drink it.
4. We have to make a wheel round. To do this, we lay the rim details on the template. According to the external contour, they draw a circle and cut down on this markup. Inside there will be a hexagon, but outside the circle.
5. As a spoke, we use ready-made round sticks. The axis, like the rim, is placed on 8 parts. We drill holes in these places.

All items are ready. We will collect the wheel, while all glue connections are:

• we put the needles with one end in the axis;
• the opposite end of the spokes insert the rim into the details;
• in the queue, gluing the parts of the rim, for which we spread them to the plane, lubricate the ends with glue and we pull everything together with a solid rope. So that the product is not swollen, we put the cargo on top;
• when the glue dries, we remove it with the remnants and protect the sandpaper, cover the veil and varnish.

In this video, the process of making a wooden wheel with curly spokes is shown:

Now, when you got acquainted with several options, make a garden cart do it yourself no problem for you. It remains to choose a suitable. The author of this video it turned out to be at all worse than the purchase: