To attract birds to the site, feeders and birdhouses are successfully used, with their help you can not worry about the safety of the future harvest. Almost all kinds of birds are settled in such houses. In the cold, they eat winter caterpillars, in summer - pest larvae.

You can make a birdhouse with your own hands without spending money from your pocket. After all, it is not necessary to buy new building materials, it is enough to include fantasy using sweater.

Materials from everyday life

One of the easiest options is a birdhouse from the box. For its manufacture, use a box from under the juice, it is thoroughly wash and dried. The advantage of this decision is considered: efficiency, original appearance and ease of execution. Materials will need:

• clean box;
• thin wooden planks;
• acrylic paint;
• rope;
• glue.

It is worth to prepare the following tools:

• scissors;
• knife;
• brush.
  

Work starts from the manufacture of anlet-pilot, it should have a diameter of 5-6 cm, while placing on medium height from the bottom of the box. Cut hole will help the usual or stationery knife. Next, the nesting is covered with paint, leave dry.

For the manufacture of a barbell, on which birds will sit, you can use a wand from ice cream. It is glued to the base under the pilot.

The inner space in the bin should also be convenient for birds, so the front wall from the inside needs to be made rough. Therefore, there is a plate of raw wood, a piece of tree cortex will also fit. The outer walls are also glued with chopsticks from ice cream - it will add aesthetics and will allow you to cling to birds with my paws.

To hang the birdhouse on the tree, the hole is done on top, pass the rope. To attract birds, it is enough to pour a bit of feed, then the family of feathered will be settled in the house.

A large plastic container can be used as the basis of the rebel. In the manufacture of a birdhouse from a bottle, the course of the process will not change, only you have to make drainage holes at the bottom.

Cardboard - a practical option

For the resettlement of the largest number of birds, it is worth making a borderboard from cardboard - this is the most affordable material. The resulting house can serve as a decorative element of the garden or used for its intended purpose. The process of execution is very simple, does not take much time. During the work, you will need:

• two cardboard sheet A4;
• colored paper or paint;
• compass;
• scissors;
• rope;
• small wand.

As a workpiece, it is watching the drawing or make on simple recommendations.

The basis of the future design is a sheet glued into a roll, you can take the remainder of paper towels. On it, the circulation is drawn a circle with a diameter of 4-5 cm, a hole is cut. Further, the bottom closes around the corresponding size - the base of the benchmark is ready. To attract attention to it decorated, you can enclose with colored paper or paint.

The manufacture of the roof starts from the cutting of the semicircle, then glue the straight edge. A thin rope is glued to the top of the dome, combine with the base. It will only be left to glue a wand near the flyer and pour food. Such a feeder can take guests for a long time or just decorate the garden.

Wood - Standard Production

There is a traditional version of the house of a tree from a tree. In the process use:

• boards (20 mm thick);
• nails;
• hacksaw;
• hammer;
• drill;
• pencil and ruler.

Of the wood materials, it is not a planed board with a thickness of at least 20 mm. This ensures the maintenance of heat inside the house. As for the breed - Birch or oak is better fit, the smell of the needles is very scared by birds. The use of pressed or glued wood is undesirable - this is not a practical option with toxic smell.

After selecting the material, the dimensions of the structure are determined. Based on the parameters of the natural heap (120x120 mm), it is worth producing a bottom of a twist at 120x120 mm, the height should be 250-350 mm. Such dimensions allow you to accommodate a family with 5 chicks. With more offspring, adults cannot provide them with proper care. Also take into account the size of the pilot, the hole 40-50 mm, the tit is made, 30 mm. The pilots are placed at an altitude of 200 mm from the bottom level.

Before entering the house, the pranch is fixed, sometimes a small platform from the board is installed instead. The roof can be a bartal or single one, but it is worth considering one point - the board must perform for the level of the facade at least 50 mm. For the convenience of annual cleaning, the roof is made removable, then it is fixed with screws or wire. All sizes of elements can be seen in the drawings.

Before making a birdhouse with your own hands, it is worth considering the scheme carefully, then according to the parameters in the image, the boards cut off. Process course:

• immediately drill a hole-pilot with a drill and a ring saw;
• the facade is nailed to the sidewalls;
• fix the bottom and rear wall;
• install a pranch or pad in front of the pilot;
• make a roof;
• screen the bar to the back wall, which fixes the birdhouse to the tree.

To make a good birdhouse from a tree worth guided by recommendations:

• for sealing and maintaining heat inside the design costs all the cracks to rinse the clay or close the packles;
• the surface of the wood should not have large sowing, which are embraced by birds;
• need to use not long nails or self-tapping screws so that they are not sticking out;
• as a protective coating, it is better to handle olphos. But for the decor you can apply oil or red oil paints.

It is not difficult to make an independent house for birds, if you connect fantasy, the result will become a real garden decoration. In the process of manufacturing a birdhouse from improvised materials, the most unpredictable basics options can go: pumpkin, stone, coffee pot, shoe.

Installing a house

In addition to manufacturing, the process of installing a birdhouse is important, so it is worth knowing the recommendations for its placement:

• place the house for birds is needed at an altitude of about 3 m, then the feathers will feel safe;
• the birdhouse after fastening on the tree should remain under a slope forward. Such a position helps to get out the bird from the inside;
• the pilots are sent to the southern direction so that the wind does not bloom inward;
• if you attach a house near the harvest site, then in the future chicks will help fight pests.

You can make a birdhouse at any time of the year, but it should hang in the tree at the end of March - early April. Then the family of feathered will be settled in it.