Modern offers of enclosing structures are not limited to the use of metal or wood. For example, professional flooring contributes to the rapid and timing erection of reliable protection. Its popularity is due to excellent characteristics and practical operation.
Content
- Honored popularity
- yandex_partner_id \u003d 22445; yandex_site_bg_color \u003d 'fffff'; yandex_ad_format \u003d 'direct'; yandex_font_size \u003d 1.0; yandex_direct_type \u003d 'vertical'; yandex_direct_border_type \u003d 'ad'; yandex_direct_limit \u003d 1; yandex_direct_title_font_size \u003d 2; yandex_direct_links_underline \u003d true; yandex_direct_bg_color \u003d 'fffff'; yandex_direct_border_color \u003d 'fffff'; yandex_direct_title_color \u003d '0C77EC'; yandex_direct_url_color \u003d '000000'; yandex_direct_text_color \u003d '000000'; yandex_direct_hover_color \u003d 'CC0000'; yandex_direct_favicon \u003d true; yandex_no_sitelinks \u003d true; document.write (''); (adsbygoogle \u003d window.adsbygoogle || []). Push (());
- Construction opportunities
- Making and mounting
Such a fence requires an appropriate continuation, so it is important to consider how to make the gate from the professional flooring with your own hands.
Honored popularity
To begin with, it is worth estimating the advantages of structures from the professional flooring, which ensure the prevalence of this material among the owners of cottages and country sites. Among the mains are distinguished:
- reliable protection against penetration, wind, dust;
- soundproofing properties;
- modern appearance;
- ease of installation;
- long service life without loss of initial qualities;
- no need to care.
As for the construction of the gate from the professional flooring, the whole process will not take much time and finance. For their installation, it will only be necessary to determine the type of gate, prepare materials and secure the main design. The advantages of the gate from the professional sheet are as follows:
- design options are possible - swing, retractable or swivel-lifting;
- the market offers a wide palette of the coloring of the trim;
- coating resistance during operation;
- service life of about 25 years.
Construction opportunities
From existing options, the swollen gates are the most common due to the simplicity of the device and the availability of the process. This design is the sash, trimmed by a professional flooring. They are attached to the hinge fences columns, the softness and smoothness of the progress provide racks with bearings. Directly, one or two sashs can swapped both outside and inward - it all depends on the convenience in each case.
Retractable gates from the professional flooring suggest the movement of the sash for the fence section when opening. In this case, the movement should be carried out in parallel. The convenience of this option is to save space and the possibility of installing an automatic mechanism. Thanks to the lightweight material, you can purchase a low-power drive, which will be quite acceptable in the financial plan. A distinctive feature of this type of gate is the maximum working width, which is 12 m.
Making and mounting
Since the disintegration of the design is considered the most common, it is worth considering its manufacture. In any case, before the manufacturing process, all measurements always remove and make up the drawing of the gate of the corrugated floor. It indicates the exact parameters of the future design and the location of all components on a comfortable scale.
Swing Gate - Simple Solution
The following components will be required for the design:
- supports - metal pipes with a diameter of 10-20cm or channel;
- support plates and 4 or 8 loops with a large core;
- metal pipes for frame;
- sheets of professional flooring;
- screws.
Next, calculate the consumption of materials and prepare a platform for mounting. For this, two holes depth from 80 to 120 cm are digging at the locations of the reference pillars, while the width should leave 30 cm. As a pillow on a bottom of a small layer, crushedane falls asleep. In the prepared pits, the supports are inserted and poured with concrete mortar, leave until complete drying. The solution is prepared with the proportions of 1: 3: 3, that is, one portion of cement goes, respectively, three pieces of sand and rubble are indulging in clean water.
Immediately before the manufacture of the gate from the corrugated floor, it is necessary to weld the support plates to the columns, they will subsequently fasten the loops. The number of the latter is 4 or 8, depending on the selected sizes and weight of the flaps, use two or four pieces per canvas.
Next, we make the frame of the gate, it is solid, and then divided into two sash. Therefore, a rectangle is welded from the pipe according to the measurements. Inside, 2 more pipes are fixed, the distance between them leaves about 8 mm. The finished frame is collected by the grinder into two parts between the pipes in the middle. It remains to cut off the sheets of frame size and fasten them with screws, hang a loop.
The installation process is to install the loops on the support pipes.
Sliding gates
The next option of the popular gate is the retracting design, it is not so easy to make it, but it's quite real. For this, you will need the following resources:
- guide profile as a rail of 6 m long;
- carriages with rollers;
- slippers top and bottom;
- top and end rollers for guide;
- circuit breakers;
- fastening system;
- screwdriver;
- perforator;
- level;
- plumb;
- welding machine;
- grinding machine.
- The process begins with the arrangement of the foundation, a hole of about 2 m is digged under it, 1 m deep and about 0.4 m wide. The concrete pillar will be labeled and parallel to the mortgage system. Next is preparing a metal mortgage design consisting of a channel 16-20 cm and reinforcement 10-14 mm. Such a frame is laid with legs down and poured all with a concrete solution by the level of the chapellery.
- This foundation for a durability requires not less than a week, during this time you can make directly the design of the sliding gate. In the case of an automated system, the plate is fixed before concreting on the channel on which the drive will be fixed. Accordingly, the plate is not filled with a solution, but remains upstairs.
- The frame requires the preparation of pipes 50x50x2 mm, a variant 60x30x2 mm is possible. For this, they are purified and treated with solvent, then an anti-corrosion primer. Next, weld pipes in the form of a future canvase, there should be no holes at the joints. The inner frame for fixing the sheath is made from the pipe 40x20x2 mm, it is fixed around the perimeter of a larger frame, that is, on the pipe 50x50x2 mm. Pipes are welded every 20-30 cm, the welding places are treated with a grinder and covered with primer.
- As a coating, enamelled paint is used for outdoor use, be sure to apply 2-3 layers. Next, the frame is trimmed with sheets with self-tapping screws or rivets.
- The installation of the gate type begins with the installation of roller carriages on a concreted channel, the rollers are fought in the guide - thereby put the gate. Fastening the carriages is carried out with welding, it provides reliable compounds designed for long-term operation.
- It is necessary to take care of a mortgage tube in advance for fastening the upper rollers and catchers, for which the pipe 60x30 mm is used. She should go to the entire height of the pillar and in the places of fittings. It is also welded to three pieces of fittings derived from the support pillar.
- The end roller is inserted into the guide rail, while in the desired position, the clamp is fixed. Next wear plugs on the rail, subsequently they provide protection against moisture. The design is ready for use after checking installed components.
