Very often, when repaired in the house and apartment there is a need to replace interroom doors. If you adhere to all the rules of installation technology, these work can be performed by the personnel without attracting specialists. About how to install a wooden interroom door with good elements with your own hands, let's tell me further.

Types of Sobor and Door Boxes for them

When replacing interroom doors, the situation is quite often occurring when the wall thickness is much larger than the width of the door frame. Especially often with this problem, residents of brick houses are faced. The fact is that when brickwork, the thickness of the walls of the lower floors is always greater than the upper, which causes a large thickness of the doorways. And the elements of door boxes are usually produced standard width. You can solve this problem in two ways:

• Installation of slope. You can make it like a putty, subsequently closing it with wallpaper and from plasterboard or plastic. This design has its advantages and disadvantages. Among the advantages can be called the cost of such a finish. The disadvantage is what makes such an operation if the premises is not carried out, quite problematic.
• Installation of volunteers. This technique allows you to close the doorway with decorative straps in the color of the box and the door canvase. At the same time, the installation of the door to the challenges allows you to make the opening of the opening without prejudice to the decoration of the adjacent walls.

If earlier the selection of elements for door boxes was limited to several types of boards, now you can choose any model you like for any design interior of the room. Boards for installing the door frame are now sold under the standard door, and the coating of their surface with a veneer allows not to cover them with varnish and paint. Door boxes are two types:

• With end groove.
• Without an end groove.

If you plan to install good, it is better to choose a door frame with a groove. In this case, the good will be attached to it without applying fasteners. If you buy a box without an end groove, then the good will have to be attached to the slope of the doorway with the help of dowels or self-tapping screws. The groove connection look more accurately and does not provide for the drilling of a task.

DOOR, as a rule, made from a veneered board or laminated fiberboard. Thanks to this, their cost is reduced, and it also appears to accurately choose them under the color and texture of the box and the canvas. Dobors are produced different widths. This allows you to choose them exactly in the thickness of the doorway, depending on the size of the box.

Installing the Box of the Interior Door with Dogs with Pas

Installing a box with good elements that are equipped with special grooves, nothing complicated. This is done in the following way:

• First of all, you need to install a box with a doorway door (in the doorway). To do this, it must first collect it. This can be done independently or order an assembly in the store, where the door was purchased.
• Racks and crossbar of the door frame canvate laid out on the floor together with the web. The design is going around the canvas with small gaps. On the elements of the box are made of marks for which the necessary lengths are cut off. The box is going together. If it does not provide for the threshold, below should be selected to the temporary bar so that the racks are not trapped when installed. This will greatly facilitate the process.
• After the box is collected, it can be installed in the opening. It is exhibited by level and is attached to the walls of the opening with the help of self-sufficiency. After that, the level of installation is checked again. Next, the gaps between the box and the doorway are filled with mounting foam.

• After the foam is driving, you can install the challenges. Before installing, you can hang the door on the loop, it will definitely not interfere.
• Next, it is necessary to measure the height of the doorway and its width. You need to cut the elements of the good.
• The next step is to measure the width of the slope (the walls of the opening, which do not close the door frame). It is necessary to do this at least three points: from above, bottom and in the middle. According to the measurement results, the clutch clutch is carried out. If the width of the slope at different points is different, then insert it better in the furniture workshop, which has more accurate equipment for this. In addition, there will be able to beat the edge to the end of the good.
• After the goodness is ready, they can be mounted on the box. The first thing is inserted into the groove of the upper good, and after it the side. When installing a problem, it is necessary to check the quality of work. So, their position relative to the plane of the door frame should be at a right angle.

• Understanding is fixed with liquid nails or self-tapping screws hidden under decorative traffic jams. You can fix good with the help of an ordinary painting scotch. In this case, not the latter will not give the placams to disperse on the parties.
• The gap between the slope and the task is blown by the mounting foam. After it dries, it is necessary to cut it out of surplus, which protrude out. To do this, you can use a wallpaper knife.
• When foam cut, you can install platbands. They are attached to the hard with small nails. In order for them to be less noticeable, you can bite the "bite off" with the hat.

Step-by-step instructions for installing interroom doors with a good non-groove

If the manufacturer of the door frame does not provide a mounting groove for the installation of goodness, the situation is somewhat more complicated. Installation of the door and boxes does not differ from the above method. It is assembled on the floor, and then mounted on the installation place with the help of anchor bolts. The distance between the walls of the doorway is filled with mounting foam.

After the foam dry and removes its remnants, you can start the installation. To do this, you will need some tool for installing the door with a good story:

• Faceless tree knife.
• Ordinary hacksaw.
• Corolnic
• Building level.
• Level.
• A sharp knife.
• Mounting foam and greasy tape.

Procedure for work:

1. Using a ruler or other measuring instrument, you must measure the width of slopes. It is necessary to do this at several points. This uses a construction level. It is applied to the wall that is adjacent to the doorway.
2. Then, with the help of a carbon or ruler, a distance from the box is made to level. This will be a good width. According to these values, it is cleaned with the help of the end handing. If the wall curve and distance at different points will differ much, then insert good is better in the furniture workshop. Unlike sampling with a groove, the edge in the case should be blocked on both sides.
3. After the kind are ready, you can start by installing them. In this case, the method of their attachment depends on how the slopes are made. If they are plastered, it is possible to fix a good-to-sleep. Otherwise, it will be necessary to make substrates from a wooden rail, and there is already a good plank for them. The rack thickness should be such that the good become as much as possible.
4. Rake to the walls is attached with the help of a dowel. It should be attached reliably, because it will be the basis for the whole design. The holes are drilled in the diameter of the dowel with sweating, it is inserted into the hole in the wall, and the nail is clogged inside. Ideally, the slats should be 3 on each side, but the average can not be installed. The top planks are installed in such a way that the upper good has spread.
5. After all the substrates are ready, you can install good things. The top plank planets on the upper substrates and grudges tightly to the box. Then the side planks of the challenges are installed. They are attached to the substrates with the help of self-tapping screws. The latter heads are closed with decorative inserts.
6. When good is attached, the correctness of their installation is checked. If everything is done perfectly and the good faces are in terms of the surrounding walls, you can fill the space between it and slightly fill in the mounting foam. As soon as it dries, its remnants are removed and platbands are attached to the challenges. This is done with nails.

Installing a steel door with a good

This problem is especially relevant in old houses, where the width of the doorway is very large. To install a problem on its inner decorative side, you must make a groove of 10 mm from the edge. To do this, you can use a disk saw. The depth of the groove should be 1/3 of the thickness of the challenge, and its width is 1 mm more than the thickness of the corner from which the box is made. Fastening of good slats is carried out using the groove to the corner of the door frame.

Installing the interior door with his own hands. Advice

Tips for the installation of interior doors with bad peers:

• The most important thing in this work is not to create yourself of unnecessary problems and difficulties. The installation of goodholds should not turn into a protracted process with drawings, calculating the conversion and complex calculations. These elements do not carry any effort, so they can simply be placed on the mounting foam.
• Additional drilling holes under the dowel looks not quite aesthetic. It is also not worth navigating the top good to the side. It will take a lot of time and effort, and a nail, if it goes wrong, it wondered, can make a lot of trouble. Click the upper bar to the side can be using wooden wedges.
• When installing good, you should not collect them together. Many masters to simplify the task are exactly this way: they put a complete design, and try to install it on a box one. This only seems easier at first glance. When moving the finished design, the side racks can be squeeed, and nails will simply spoil the appearance of the good, and it will not be possible to close the crack. It is better to collect everything "at the place."

Door with a good: video