Simulation of a bar is a board with a thickness in the range of 16-45 mm, of which the special-shaped panels are manufactured. They are used for the outer, as well as the interior decoration of the walls. Brous imitation installation technology and other information about the material is set out in this article.

Bruus Simulation Basics

Due to the processing of antiseptics, the panel in the form of a bar is well withstanding the effects of atmospheric precipitation. The imitation of the bar externally and in its characteristics is practically not inferior to the lining of natural wood. The difference is that the imitation of the timber is more massive, and the surface is better processed. Other features are as follows:

• resistance to changes in humidity and ambient temperature;
• good heat insulating properties;
• the ability to hide engineering communications laid on the walls of the building (cables, water pipes, ventilation channels);
• low share;
• strength: During operation, there is no longitudinal and transverse cracking.

Note: The feature of the imitation design is in the method of removing condensing moisture through the grooves located on the back side.

Installation of timing of timber: preparatory stage

It must be borne in mind that wood from which a false-timber is made may contain residual moisture after drying - up to 14 percent. In order to avoid deformation, the material should be withstanding several days in operating conditions. Imitation of a bar is placed under a canopy of several rows, between which, with a 40-50 mm thick bars, a gap for ventilation is ensured. Further preparatory work implies the following.

Holding the simulation of timber in operating conditions will help to avoid material deformation

1. Mounted vertical lattice from bars with a cross section of 40 × 40, 40 × 50 or 50 × 50 mm. The distance from the base wall is chosen depending on the maximum deviation of it (as well as angles and adjoining walls) from the vertical position. Between the bars of the crates, the interval is 40-60 cm.
2. All materials made of wood are processed by antiseptic agents and antipirens.
3. For insulation of the house between the bars of the rim, plates made of mineral wool are laid.
4. Mounted vapor barrier membrane. Neighboring canvases are stacked with an allen at least 10 cm. The membrane is attached over the insulation - to the bars with the help of a bracket and a furniture stapler.

Falsh-timber mounted on top of a vaporizolation membrane

Important: With the help of the crate you can hide defects. Before mounting the bars, it is necessary to determine the irregularities of the walls and set it up, at what minimum distance do the lamp should be located. Initially, its elements are installed in the corners, and then, with the help of a stretched cord, the other bars are exhibited.

Methods for fastening timing of timber

Brous imitation laying technology prescribes to start its attachment from below, moving gradually upwards. It is recommended to retreat 15-20 cm so that the lower false bars does not stretch the rain and snow. For further installation, you need to select one of the following methods.

1. Mounting with nails: nails with galvanized coating are used to avoid the formation of rusty leaks on wood. They are driven through the spikes so that the hammers are not formed from the blows.
2. Fastening with self-drawers: Installing the simulation of a bar with their own hands inside and outside the screwing of the self-tapping screws at an angle of 45 degrees in the spike. Another option is to screw the screws into the middle part of the false timber, for which a deaf hole is drilled to the middle of the thickness, the diameter of which is equal to the diameter of the Hat. Subsequently, the holes close to a spacade on a tree, selected in color or wooden plugs (fixed with PVA glue).
3. Fixation with steel cleimers. The method has several advantages over others, as it allows you to secretly strengthen them on the wall and damage. About how the installation of timing of timber is performed with their own hands inside the house - video with explanations of the specialist.

Tip: Determining how to work with timber imitation, it should be borne in mind that klyamimers are unreliable for outdoor use. With their help, a false-timber indoor is fixed.

Failure Fastening Scheme

Basic Rules for Mounting Simulation Bruus

The algorithm of action when installing the simulation of the bar consists of the following items.

1. On the entire perimeter of the walls, it is necessary to mark the position of the position of the lower (first) board. This is recommended to use the water level.
2. The first board is fixed to the crate in two places: at the bottom and above.
3. The next board is superimposed on top and connects to the bottom method of Schip-Groove. The mount is carried out only at the top.
4. Topboard, if it does not fit entirely, clipped in size using a circular hand saw or an electric bike.
5. The panels in the corner are docked at an angle of 45 degrees, for which they are roasted before installation. At the place of the joint on both sides, vertical racks of the crates must be installed.

Features of the installation of timing of timber inside the house

Before establishing a timber imitation inside the house, it is necessary to determine how successfully the material will match the overall design concept. If it is required to support the village interior design style, the false-timber will be the best solution. In addition, with the help of this material you can zonate the premises.

The surface of natural wood looks "warm" and aesthetically attractive

Installation technology does not differ from the above, if the base walls are not characterized in quality. In the event that they are smooth and not deviate from the vertical, it is possible to mount a false-bar without a crate - directly to the wall. This will help save money and minimize the loss of room volume.

Important: Lock the insulation on the inner surfaces of the wall under the simulation of the bar is possible only after the insulation of the house from the outside. Otherwise, the line of freezing the wall (dew point) is shifted towards the room.

Driven nails in the spike so that the place of the attachment was not noticeable

Using the article of the article on how to navigate the simulation of the bar inside the house, you can independently create an original interior.