Modern renovation has already ceased to be a long process with a large amount of dust due to new materials and technologies. Plasterboard allows you to embody many variety of designs without loss of quality in a short time. This is the perfectly smooth surfaces that can be saved or painted, it all depends on the taste preferences of the customer.

But before applying the finish coating of the design, they need pre-trim, the technology of preparation of drywall is in front of painting one.

Sequence of the process of preparation of plasterboard surfaces

To obtain a qualitative result, you must adhere to such operations:

1. verification of the state of the surface;
2. padding;
3. puttling of junctions between sheets;
4. fastening of sickle tape;
5. alignment of the total surface with spatlement;
6. sanding;
7. re-priming.

Required tool kit

When preparing drywall, it will take such a set of tools:

• screwdriver;
• laner knife;
• brush;
• two spatulas;
• mixer;
• portable lamp;
• small skin.

For high-quality work, it will take a small and large spatula, fully suitable width of 100 and 250mm. They are convenient not only to dial the mixture, but also to distribute according to the design. The mixer is necessary for the preparation of the working solution, it helps to get a homogeneous consistency composition, without lumps. The skin of the same removes small nuances on an ochpatle surface, smoothing it.

Necessary materials

Technology of gypsum carcarter under painting provides a standard set of materials:

• directly a mixture for spatlement;
• primer;
• sherryanka ribbon;

Putclone and primer should be designed to work with plasterboard, stores offer many options that differ in price and quality. Materials are better to choose an average cost from the well-known, proven manufacturer. It is advisable to choose the finished mixtures, but putty mainly require dilution with water, then the preparation is performed according to the instructions on the package. Sherryanka ribbon, it is the same reinforcing tape, used to obtain high-quality connections. So you can avoid cracking of the finishing layer, which may appear after the end of the repair work.

Process description

1. Prepare plasterboard to paint enough simply, especially if there are step-by-step recommendations. The whole process begins with checking the condition of the surface, for this, the location of the self-containers are viewed. According to the rules, they screw in 5mm deep into the material, with a deeper flooding they will have to be screwed using a screwdriver in several centimeters from the already made hole. Next, the joints with a painting knife are needed - this is necessary for better clutch of the solution with plasterboard. The extending is cutting the edge of the sheet at an angle of 45˚, as a result, approximately 5mm from each sheet is removed.

2. The processing of drywall under painting continues priming, which increases the quality of the adhesion of the finishing layer with a rough surface. This is ensured by the presence of adhesion fillers in the composition of the soil, in addition, the solutions have antifungal properties, which is important for the successful operation of the structures. For ease of use, many manufacturers paint the compositions in yellow or pink color, it contributes to uniform applying soil over the entire surface of the structures. Apply primer with a wide brush, layer after drying should be less than 0.03mm.

3. Directly putting the plasterboard under painting begins with sealing joints. Empties are filled with a mixture with spatulas, the putty is rubbed, closing all the gaps. It is worth carefully monitoring the uniformity and completeness of filling voids, it will eliminate unwanted manifestations.

4. The serpnyanka ribbon is made of fiberglass, it is easily attached to the surface by impregnating the adhesive composition. It closes the joint, it acts as fittings and enhances the connection.

The price of plasterboard putty under painting depends on the selected materials and skill of specialists. The compositions should not save, German and Finnish companies are considered the best manufacturers. And the cost of work depends on the type of surfaces, the processing of figure structures requires greater skill from the artist, rather than even smooth surfaces.
6. After drying, the putty must be carefully walking on the surfaces of the skin, so the smooth walls and the ceiling are obtained. The shortcomings are removed and excess the mixture is erased. First you should use coarse sandpaper, then walk on the surface of the skin with small grains. If you know how to properly sharpen plasterboard to paint and follow the recommendations, the result obtained will be high-quality and durable.
7. Re-priming is performed in two layers, this technology allows you to finally prepare designs for painting. In addition to providing the clutch of paint with a surface, double priming prevents the intensive absorption of the applied finish finish. So the paint consumption is reduced and a uniform distribution of the composition on the surfaces is achieved.

Quality preparation - a key to obtaining a good result

Preparation of walls or ceiling from drywall under painting does not differ in technology, it is important to carefully treat all parts of the structure. As paint, experts recommend using water-emulsion formulations. It should be borne in mind that glossy surfaces give all nuances of preliminary preparation, and matte make it possible to hide small nuances. In confidence in our own power, the whole process will fully implement it yourself, but it is quite troublesome. That is why many leave work with plasterboard specialists.